System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1) Copyright (c) 1999 by cisco Systems, Inc. C1600 platform with 8192 Kbytes of main memory program load complete, entry point: 0x4020060, size: 0x165eac %SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader. program load complete, entry point: 0x2005000, size: 0x21f936 Self decompressing the image : ################################################# ######################### [OK] Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) 1600 Software (C1600-Y-M), Version 12.0(12), RELEASE SOFTWARE (fc1) Copyright (c) 1986-2000 by cisco Systems, Inc. Compiled Mon 10-Jul-00 19:59 by htseng Image text-base: 0x02005000, data-base: 0x0245E484 cisco 1601 (68360) processor (revision C) with 6144K/2048K bytes of memory. Processor board ID 23099315, with hardware revision 00000003 Bridging software. X.25 software, Version 3.0.0. 1 Ethernet/IEEE 802.3 interface(s) 1 Serial(sync/async) network interface(s) System/IO memory with parity disabled 8192K bytes of DRAM onboard System running from RAM 7K bytes of non-volatile configuration memory. 4096K bytes of processor board PCMCIA flash (Read/Write) --- System Configuration Dialog --- Would you like to enter the initial configuration dialog? [yes/no]: yes At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system Would you like to enter basic management setup? [yes/no]: yes Configuring global parameters: Enter host name [Router]: hoge-gw The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter enable secret: password1 The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images. Enter enable password: password2 The virtual terminal password is used to protect access to the router over a network interface. Enter virtual terminal password: password3 Configure SNMP Network Management? [yes]: yes Community string [public]: HOGE Current interface summary Any interface listed with OK? value "NO" does not have a valid configuration Interface IP-Address OK? Method Status Protocol Ethernet0 unassigned NO unset up down Serial0 unassigned NO unset down down Enter interface name used to connect to the management network from the above interface summary: Ethernet0 Configuring interface Ethernet0: Configure IP on this interface? [yes]: yes IP address for this interface: 202.144.158.253 Subnet mask for this interface [255.255.255.0] : 255.255.255.240 Class C network is 202.144.158.0, 28 subnet bits; mask is /28 The following configuration command script was created: hostname hoge-gw enable secret 5 $1$Tk3z$5NlqsaYCojkq4cNoXl6sG1 enable password password2 line vty 0 4 password password3 snmp-server community HOGE ! no ip routing ! interface Ethernet0 no shutdown ip address 202.144.158.253 255.255.255.240 ! interface Serial0 shutdown no ip address ! end [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. Enter your selection [2]: 2 Building configuration... Use the enabled mode 'configure' command to modify this configuration. Press RETURN to get started!